Plastics processing · Extruders on a VFD · Quote by machine duty
Plastic Machinery Motors
Our contact page lists plastic machinery among the uses of our motors, and our industries page puts plastics under manufacturing. We do not publish ratings for particular plastics machines, so this page sorts the drives by load type, names the series to start from, and lists what we need to confirm the motor.
Plastics drives by load type
A plastics line has drives with very different loads. The series below are the ones our manufacturing, YVF2 and catalog pages name. The right column is what we confirm with you; we do not guess it.
| Load type | Series to start from | What our sources state | Confirmed with the quote |
|---|---|---|---|
| Screw drive on a frequency converter | YVF2 inverter duty | Our YVF2 page: S1 continuous duty at low speed, suited to extruders; constant torque 5–50 Hz; separate cooling fan | Screw torque across the speed range, gearbox ratio, converter make |
| Fixed-speed main drives and mixers | YE3 or YE4 | Our manufacturing page: high starting torque for mixers and high-inertia loads, S1 duty | Starting load, inertia and starts per hour |
| Compressors and general processing | YE3, YE4 or Y2 | Our industries page: continuous power for compressors, plastics and general processing | kW, poles, mounting |
| Cooling fans and water pumps on the line | YDT for two or three speeds | Catalog: YDT designed for fans and pumps | Shaft power at each speed from the fan or pump maker |
| Geared auxiliary drives | RFKS on R, F, K or S reducers | Catalog: automated lines, conveyors and packaging | Reducer family and size |
Our manufacturing page also describes Class F/H insulation with VPI and a wide-voltage, 50/60 Hz design. The catalog tables are 380 V 50 Hz data; other voltages and 60 Hz are confirmed per order. See dual voltage motors and 60 Hz motors.

The machine duty we ask for
Send these for each drive point on the machine.
01
Machine and drive point
Extruder, mixer, granulator, haul-off or auxiliary; which shaft the motor drives.
02
Speed and control
Fixed speed, or the speed range on a converter.
03
Torque
Torque at the lowest running speed and at start, from the machine maker.
04
Duty
Continuous or start-stop; starts per hour; overload you expect.
05
Heat around the motor
Air temperature near heaters and barrels.
06
Fit
Mounting, shaft drawing, voltage and frequency.
General-purpose motors for fixed-speed drives
Grey cast-iron housing, IP55, Class F, S1, per the catalog overview.

Fixed speed
YE3 · YE4 · Y2
YE3 (IE3): 0.18–630 kW, frames 80–400. YE4 (IE4): 0.55–630 kW, frames 80–400. Y2 (IE2): 0.09–900 kW, frames 63–450. Mounting B3, B5, B35 or V1, plus B14 and others on smaller frames.
IP55 · Class F · S1 · IC411 · 380 V 50 Hz catalog data · 1-year warranty
Speed control: YVF2 series · VFD motors. Non-standard fit: OEM electric motors · custom shaft motors.
How a plastics inquiry runs
Reply
We reply to every inquiry within 24 hours, per our service page.
Technical check
Engineers check the machine duty before the quote, so the rating is confirmed, not guessed.
Quote and sample
A quote in under 12 hours once the data is complete, and a single engineering sample for bulk and OEM orders.
From our service page. Every motor passes ten routine tests and ships with its own data sheet, per our quality page.
Send your machine duty
One line per drive point is enough to start.
- Machine type and the drive point
- Speed: fixed, or range on a converter
- Shaft power, and torque at start and low speed
- Duty: continuous or start-stop
- Air temperature near the motor
- Mounting, voltage, frequency and quantity
Jiangxi Jiawang Special Motor · +86 199 0684 4761 · [email protected] · 1-year warranty on all products
Plastic machinery motor questions
Which motor for an extruder screw?
If the screw runs on a frequency converter, start from YVF2: our YVF2 page names extruders and S1 duty at low speed, with a separate cooling fan. We confirm the size once you send the screw torque and speed range.
Do you publish torque ratings for extruders or injection machines?
No. We do not publish machine-specific torque or power ratings. The machine maker’s data decides the motor, and we confirm the model with the quote.
Which series for mixers and other fixed-speed drives?
YE3 or YE4. Our manufacturing page describes high starting torque for mixers and high-inertia loads. Y2 remains an option where first cost matters most.
Can the motor sit near heaters?
The catalog operating conditions give an ambient of up to +40 °C. If the air near the motor is hotter, tell us; Class H insulation is available on request.
Do you supply the gearbox?
We make the motor. RFKS motors fit R, F, K and S reducer families, and our flange motors mount directly on a gearbox input.
What warranty applies?
1 year on all products.
