Shaft to drawing · Double shaft · In-house machining
Custom Shaft Motors
When the standard shaft end does not suit your coupling, pulley or machine, we make the shaft to your drawing, whatever the diameter or length, or add a second shaft at the non-drive end. Shafts are machined in our own workshop.
Four ways to change the shaft
Just send us your drawing. These are the options our customization and product pages describe.
Custom dimensions
Manufactured exactly to your drawing, so the motor fits your machine whatever the shaft diameter or length.
Double shaft
Shaft extensions at both ends, drive end (DE) and non-drive end (NDE). Connect two loads, or fit a brake, an encoder or another accessory.
Encoder-ready NDE
On the YVF2 variable-frequency series, the NDE shaft and end shield include an encoder mounting interface for closed-loop control.
Gear reducer input
On RFKS motors, a custom shaft extension goes straight into an R, F, K or S reducer and works as the first-stage pinion.
The standard shaft ends, for reference
Start from the catalog shaft, then mark what has to change. YE3/YE4 values, by frame and pole count.
| Frame | Poles | D shaft dia. | E length | F key width | GA | DH centre hole |
|---|---|---|---|---|---|---|
| 80 | 2–8 | 19 | 40 | 6 | 21.5 | M6×16 |
| 90S | 2–8 | 24 | 50 | 8 | 27 | M8×19 |
| 90L | 2–8 | 24 | 50 | 8 | 27 | M8×19 |
| 100L | 2–8 | 28 | 60 | 8 | 31 | M10×22 |
| 112M | 2–8 | 28 | 60 | 8 | 31 | M10×22 |
| 132S | 2–8 | 38 | 80 | 10 | 41 | M12×28 |
| 132M | 4–8 | 38 | 80 | 10 | 41 | M12×28 |
| 160M | 2–8 | 42 | 110 | 12 | 45 | M16×36 |
| 160L | 2–8 | 42 | 110 | 12 | 45 | M16×36 |
| 180M | 2–8 | 48 | 110 | 14 | 51.5 | M16×36 |
| 180L | 4–8 | 48 | 110 | 14 | 51.5 | M16×36 |
| 200L | 2–8 | 55 | 110 | 16 | 59 | M20×42 |
| 225S | 4–8 | 60 | 140 | 18 | 64 | M20×42 |
| 225M | 2 | 55 | 110 | 16 | 59 | M20×42 |
| 225M | 4–8 | 60 | 140 | 18 | 64 | M20×42 |
| 250M | 2 | 60 | 140 | 18 | 64 | M20×42 |
| 250M | 4–8 | 65 | 140 | 18 | 69 | M20×42 |
| 280S | 2 | 65 | 140 | 18 | 69 | M20×42 |
| 280S | 4–8 | 75 | 140 | 20 | 79.5 | M20×42 |
| 280M | 2 | 65 | 140 | 18 | 69 | M20×42 |
| 280M | 4–8 | 75 | 140 | 20 | 79.5 | M20×42 |
| 315S | 2 | 65 | 140 | 18 | 69 | M20×42 |
| 315S | 4–10 | 80 | 170 | 22 | 85 | M20×42 |
| 315M | 2 | 65 | 140 | 18 | 69 | M20×42 |
| 315M | 4–10 | 80 | 170 | 22 | 85 | M20×42 |
| 315L | 2 | 65 | 140 | 18 | 69 | M20×42 |
| 315L | 4–10 | 80 | 170 | 22 | 85 | M20×42 |
| 355M | 2 | 75 | 140 | 20 | 79.5 | M20×50 |
| 355M | 4–10 | 95 | 170 | 25 | 100 | M24×50 |
| 355L | 2 | 75 | 140 | 20 | 79.5 | M20×50 |
| 355L | 4–10 | 95 | 170 | 25 | 100 | M24×50 |
D, E, F, GA and DH as printed in the YE3/YE4 flange-mounted and B35 dimension tables (catalog pages 27 and 28, which agree). GA is the height over the key. The foot-mounted table on page 26 prints D = 60 mm for 250M 4–8 pole and 65 mm for 280S/280M 4–8 pole; check on your drawing. Catalog values in mm. Confirm every dimension on the drawing for your order before machining a base, flange or coupling.

What to put on the drawing
A clear drawing is the fastest route to a quote. Our engineers check it in technical verification before we price it.
01
Diameter and fit
Shaft diameter at the drive end, with the tolerance your coupling or hub needs.
02
Length
Extension length from the shoulder, and any step or shoulder you need.
03
Drive feature
Keyway width, depth and length, or another feature your machine uses.
04
End features
Centre hole thread, end tapping, or anything else on the shaft face.
05
Second shaft
For a double shaft: the NDE dimensions and what it drives or carries.
06
The load
Coupling, belt or pulley, and roughly how hard it pulls on the shaft.
Double-shaft motors
One motor, two shaft ends. Useful when a second load, a brake or an encoder has to sit on the same axis.

Double shaft option
DE and NDE shaft extensions
Shaft extensions at the drive end and the non-drive end, on the same three-phase motor. Tell us what each end drives and we confirm the layout in the quote.
Built on IEC three-phase motors · Shaft to drawing · In-house machining
Need a brake on the motor itself? See the YEJ brake motor series.
Where a custom shaft helps
Machine builders
Your coupling, pulley or gearbox already exists. The shaft is made to match it.
Replacements
An old motor with a special shaft. Send the old dimensions and we machine the new shaft to them.
Two loads, one motor
A double shaft drives a second machine or carries a brake or encoder.
“They customized the shaft dimensions exactly to our drawings. Fast delivery too.” Customer review on our projects page.
Send your shaft drawing
A drawing in PDF or CAD with the base motor details is all we need to start.
- Shaft drawing: diameter, length, keyway, end features
- Single or double shaft; for double, what the NDE carries
- Base motor: kW, poles and frame, or the old nameplate
- Mounting: B3, B5, B35 or V1
- Supply voltage and frequency
- Quantity
Jiangxi Jiawang Special Motor · +86 199 0684 4761 · [email protected] · 1-year warranty on all products
Custom shaft questions
Can you make the shaft to my drawing?
Yes. Shafts are manufactured to your drawing, whatever the diameter or length, and machined in-house.
Can I get a double-shaft motor?
Yes. Double shaft extensions (DE and NDE) let one motor drive two loads, or carry a brake, an encoder or another accessory.
What shaft material do you use?
Tell us what your drawing specifies. We confirm the material in the quote.
What is the standard shaft for my frame?
See the table above: diameter D, length E, key width F, GA and centre hole DH for frames 80 to 355, from the YE3/YE4 catalog. Above frame 200, 2-pole and 4-pole motors of the same frame can have different shafts.
Does a custom shaft change anything else?
It can. That is why every non-standard request goes through technical verification before we quote: we check the shaft against the motor and the load you describe.
