Finished three-phase motors stacked on a pallet in the JWMotor plant, shafts and flanged end shields facing out

Pump stations · Sewage plants · IP55 · S1 continuous duty

Wastewater Pump Motors

Motors for the pumps that move water and sewage day and night. This page covers the three series named on our water and wastewater page, YE3, YDT and YD, with the enclosure, mounting and duty data from our catalog and the details we check before quoting a pump motor.

IP55Enclosure to IEC 60034-5; IP65 and custom sealing on request
S1Continuous duty, IC411 cooling, catalog
90%Average monthly peak relative humidity, catalog operating conditions
24/7Kunming No.13 Sewage Plant, supplied with Donglin Pump Industry

What a pump station asks of a motor

A pump motor runs for long hours in a damp room, often bolted to a pump that is already in place. These are the points that decide the motor, and what our catalog and pages state for each.

Long running hours

Catalog motors are rated for continuous duty S1 with IC411 surface cooling. For pumps that run most of the year, our water page points to IE3 and IE4 efficiency: YE3 is IE3, and YE4 is IE4.

Damp air and splashes

IP55 to IEC 60034-5 is the catalog enclosure. Our customization page lists IP55 and IP65 as standard options and offers special sealing beyond that. Windings are vacuum pressure impregnated, Class F (155 °C).

Humidity limit

The catalog operating conditions are −15 °C to +40 °C ambient, altitude up to 1000 m and an average monthly peak relative humidity of 90%. If your pump room is outside that, tell us before we quote.

How the pump is mounted

Foot mounted B3 on a baseplate, flange B5 for close-coupled pumps, or V1 vertical, shaft down, with a rain canopy for outdoor use. B14 face mounting is also offered.

Same-frame replacement

Mounting dimensions follow IEC 60072, so a same-frame motor matches shaft height, foot holes and flange. Our water page puts it simply: swap the motor without changing pipes or base.

Overheat protection

PTC thermistors, PT100 sensors or bimetallic switches can be built into the winding, as listed on our customization page.

Pump duty and the series to start from

These are the three series on our water and wastewater page. Ranges are from our catalog performance tables at 380 V 50 Hz. The quote confirms the model for your pump.

Pump dutySeriesCatalog rangeWhy this series
One speed, long hours: lift stations, transfer and process pumpsYE3 (IE3)0.18–630 kW, frames 80–400, 2 to 10 polesPremium efficiency for continuous running; grey cast-iron housing; IEC frames for same-frame replacement
Two or three fixed flows, such as day and night dutyYDT variable torque0.17–160 kW, frames 80–315; pairs 2/4, 4/6, 4/8, 6/8 and 4/6/8Designed for fans and pumps; the catalog names water treatment. Torque follows the square of speed, like a centrifugal pump
Two fixed speeds on other plant equipmentYD pole-changing0.45–82 kW, frames 80–280; pairs 4/2, 6/4 and 8/4Speed change on contactors, no converter; the catalog names flow-rate and process-cycle changes, the YD page mixers and conveyors

YDT range note: our live YDT pages give 0.45–82 kW and frames 80–280; the catalog tables run to 160 kW and frame 315. The catalog is used here. Pair sizes per speed are on multi speed motors for fans and pumps. If the pump runs on a frequency converter, see VFD motors.

Technician checking the cable gland on the terminal box of a blue motor coupled to a centrifugal pump in a pump station

What we check before quoting a pump motor

Most pump-motor problems start with a detail that was not on the inquiry. We go through these with you.

01

Nameplate or frame

kW, poles, frame and mounting from the old motor or the pump drawing.

02

Mounting and shaft

B3, B5, V1 or B14; shaft made to your drawing when the pump needs it.

03

Enclosure and sealing

IP55 standard; IP65 or special sealing when the room is wet or the motor stands outdoors.

04

Thermal protection

PTC, PT100 or bimetal in the winding, wired to your control panel.

05

Speeds and control

One speed, two or three fixed speeds, or a converter.

06

Test record

Ten routine tests on every motor and one data sheet each: resistance, hi-pot, vibration.

Pump motors from three series

All three are three-phase cage induction motors with Class F insulation and IP55 in the catalog tables.

Three blue cast-iron motors on a concrete floor: foot mounted, flange mounted and vertical with a rain canopy

For pumps

YE3 · YDT · YD

YE3 (IE3): 0.18–630 kW, frames 80–400. YDT variable-torque multi-speed: 0.17–160 kW, frames 80–315. YD two-speed: 0.45–82 kW, frames 80–280. Mounting B3, B5, B35 or V1, plus B14 and others on smaller frames.

IP55 · Class F · S1 · IC411 · 380 V 50 Hz catalog data · 1-year warranty

Series pages: YE3 · YDT · YD · two speed motors · B35 motors.

Where our motors run

Kunming No.13 Sewage Plant

In partnership with Donglin Pump Industry, JWMotor supplies high-protection motors for the core wastewater systems, running 24/7.

Jiangxi Runtian Water Plant

40 JWMotor three-phase motors across the plant’s conveying, packaging and ventilation lines.

Pump makers and repair shops

Same-frame IEC motors for pumps already in service; send the nameplate and we match frame, mounting and shaft. See same-frame replacement.

Projects from our projects page.

Quote a pump motor

Tell us about the pump and the room. We reply with the series and the data sheet.

  • Pump type and how the motor is mounted: foot, flange or vertical
  • kW and poles, or a photo of the old nameplate
  • How it runs: one speed, two flows, or on a converter
  • The room: indoor or outdoor, damp, splashing, temperature
  • Thermal protection you need
  • Voltage, frequency and quantity
Quote a pump motor

Jiangxi Jiawang Special Motor · +86 199 0684 4761 · [email protected] · 1-year warranty on all products

Pump motor questions

What enclosure do your pump motors have?

IP55 to IEC 60034-5, as in our catalog. Our customization page lists IP55 and IP65 as standard options, and we offer special sealing when the operating environment needs more.

Can a JWMotor motor replace the motor on my existing pump?

If the old motor is an IEC motor, yes in most cases: same-frame motors share shaft height, foot holes and flange. Send the nameplate and the pump mounting, and we confirm the frame and shaft.

Which series for a pump with two flow rates?

YDT. Its variable-torque windings give two or three fixed speeds on contactors, and its torque follows the square of speed like a centrifugal pump. See multi speed motors for fans and pumps.

How humid can the pump room be?

The catalog operating conditions give an average monthly peak relative humidity of 90%, ambient −15 °C to +40 °C and altitude up to 1000 m. Outside those limits, tell us and we check before quoting.

Do you make submersible pump motors?

No submersible motors are listed in our catalog. The motors on this page are installed beside or on top of the pump, in a dry pit or on a baseplate.

Are these motors for hazardous areas?

This page covers standard IEC motors. If the pump stands in an area classified for explosive gas or dust, say so in your inquiry before anything else.