IM B35 · Feet + B5 flange
B35 Motors
B35 has both: feet on the frame and a B5 flange at the drive end. The motor can stand on a base and bolt to the machine at the same time, giving it dual support. Our catalog lists B35 for frames 80 to 400. It is the flange option that continues past frame 280.
B3, B5 or B35
Same motor, three ways to hold it. The frame range is often what decides.
B3 · feet only
Feet on the frame, horizontal mounting on a baseplate. Frames 80–400. B3 motors
B5 · flange only
Large flange with through-holes and no feet, for close coupling such as pumps. Frames 80–280. B5 motors
B35 · feet and flange
Feet on the frame and a B5 flange, for dual support. Frames 80–400.
B34 · feet and face
Feet plus a B14 face mount instead of the large flange. Frames 80–112.
B3, B35, B5 and V1 are the standard mounting types in our catalog. Above frame 280 the mounting chart lists the flange only in B35 (and V1 up to 355).
B35 dimensions by frame
Foot and flange on one motor. H, A and C locate the feet; M and P are the flange bolt circle and outside diameter; S the bolt hole; D × E the shaft.
| Frame | Poles | H | A | C | M | P | D × E |
|---|---|---|---|---|---|---|---|
| 80 | 2–8 | 80 | 125 | 50 | 165 | 200 | 19 × 40 |
| 90S | 2–8 | 90 | 140 | 56 | 165 | 200 | 24 × 50 |
| 90L | 2–8 | 90 | 140 | 56 | 165 | 200 | 24 × 50 |
| 100L | 2–8 | 100 | 160 | 63 | 215 | 250 | 28 × 60 |
| 112M | 2–8 | 112 | 190 | 70 | 215 | 250 | 28 × 60 |
| 132S | 2–8 | 132 | 216 | 89 | 265 | 300 | 38 × 80 |
| 132M | 4–8 | 132 | 216 | 89 | 265 | 300 | 38 × 80 |
| 160M | 2–8 | 160 | 254 | 108 | 300 | 350 | 42 × 110 |
| 160L | 2–8 | 160 | 254 | 108 | 300 | 350 | 42 × 110 |
| 180M | 2–8 | 180 | 279 | 121 | 300 | 350 | 48 × 110 |
| 180L | 4–8 | 180 | 279 | 121 | 300 | 350 | 48 × 110 |
| 200L | 2–8 | 200 | 318 | 133 | 350 | 400 | 55 × 110 |
| 225S | 4–8 | 225 | 356 | 149 | 400 | 450 | 60 × 140 |
| 225M | 2 | 225 | 356 | 149 | 400 | 450 | 55 × 110 |
| 225M | 4–8 | 225 | 356 | 149 | 400 | 450 | 60 × 140 |
| 250M | 2 | 250 | 406 | 168 | 500 | 550 | 60 × 140 |
| 250M | 4–8 | 250 | 406 | 168 | 500 | 550 | 65 × 140 |
| 280S | 2 | 280 | 457 | 190 | 500 | 550 | 65 × 140 |
| 280S | 4–8 | 280 | 457 | 190 | 500 | 550 | 75 × 140 |
| 280M | 2 | 280 | 457 | 190 | 500 | 550 | 65 × 140 |
| 280M | 4–8 | 280 | 457 | 190 | 500 | 550 | 75 × 140 |
| 315S | 2 | 315 | 508 | 216 | 600 | 660 | 65 × 140 |
| 315S | 4–10 | 315 | 508 | 216 | 600 | 660 | 80 × 170 |
| 315M | 2 | 315 | 508 | 216 | 600 | 660 | 65 × 140 |
| 315M | 4–10 | 315 | 508 | 216 | 600 | 660 | 80 × 170 |
| 315L | 2 | 315 | 508 | 216 | 600 | 660 | 65 × 140 |
| 315L | 4–10 | 315 | 508 | 216 | 600 | 660 | 80 × 170 |
| 355M | 2 | 355 | 610 | 254 | 740 | 800 | 75 × 140 |
| 355M | 4–10 | 355 | 610 | 254 | 740 | 800 | 95 × 170 |
| 355L | 2 | 355 | 610 | 254 | 740 | 800 | 75 × 140 |
| 355L | 4–10 | 355 | 610 | 254 | 740 | 800 | 95 × 170 |
From the YE3/YE4 B35 dimension table, catalog page 28. Its foot spacing column B does not match the B3 table on page 26, so B is left out here; use the B3 table and confirm on the drawing. The B35 table ends at frame 355; frame 400 B35 dimensions are on request. Catalog values in mm. Confirm every dimension on the drawing for your order before machining a base, flange or coupling.

When B35 is the right choice
When the motor has to sit on a base and bolt to the machine at the same time.
01
Dual support
Feet on the base and the flange on the machine, both carrying the motor.
02
Flange above frame 280
For horizontal frames 315 to 400, B35 is the flange arrangement the catalog lists.
03
Like-for-like replacement
A standard IEC frame keeps the same shaft height, foot pattern and flange on YE3.
04
Vertical instead?
V1 (frames 80–355), V3 (80–160), V15 and V36 (80–100) are the vertical codes in the catalog.
Series to build a B35 on
B35 is a mounting choice, not a separate series. The general-purpose series below are where it starts.

B3 · B35 · B5 · V1 standard
IE2, IE3 and IE4 series
Y2 (IE2), YE3 (IE3) and YE4 (IE4) three-phase induction motors in grey cast iron frames, mounting dimensions to IEC 60072 and GB/T 4772.1.
B35 frames 80–400 · IP55 · Class F · S1
Or see the Y2 (IE2) series.
Where B35 motors go
Mining and aggregates
Heavy drives where the motor sits on a base and bolts to the machine.
Material handling
Conveyor drives with a flanged input.
Pumps and process
Large pumps and process machines above frame 280.
Industry pages: Mining and aggregates · Material handling · Manufacturing
Ask for a B35 motor
Tell us the frame, the flange and the base.
- Frame size, or kW and poles
- Flange M, N and P, and foot holes if the base is drilled
- Shaft D × E, or a drawing if it differs
- Supply voltage and frequency
- Efficiency class: IE2, IE3 or IE4
- Quantity
Jiangxi Jiawang Special Motor · +86 199 0684 4761 · [email protected] · 1-year warranty on all products
B35 questions
What is a B35 motor?
A motor with feet on the frame and a B5 flange at the drive end, so it can be supported by both.
Which frames are available as B35?
Frames 80 to 400 on our catalog mounting chart. Dimensions for frames 80 to 355 are in the table above; frame 400 on request.
What is the difference between B35 and B34?
B35 combines feet with the large B5 flange. B34 combines feet with a B14 face mount and is listed for frames 80 to 112.
Is a B35 motor the same as a B3 motor with a flange?
In our catalog tables the shaft height H and foot dimensions A and C match B3 for the same frame (one printed difference at 112M, noted under the table), and the flange matches the B5 flange.
Can I get a flange-only motor above frame 280?
The catalog lists B5 only to frame 280. Above that, the flange arrangement it lists is B35. Ask if you need something else. See B5 motors.
