Pallet stacks of assembled gear motors with reddish-brown reducers and grey motor housings in the workshop

R helical · in-line output · RFKS · IE3

Helical gear motors

A helical gear motor keeps the drive on one line: the output shaft runs on the same axis as the motor. That is the R reducer family. The RFKS motor goes straight into its input, with no coupling and no adapter. 0.18–630 kW in IEC frames 80–400, to IE3.

RHelical, in-line output
No adapterShaft is the first pinion
0.18–630 kWRFKS power in the catalog
80–400IEC frame, 2–10 poles

Why in-line

An R drive changes the speed, not the direction. The motor and the output share one axis.

Straight layouts

Conveyors, screws and drums where the drive can sit in line with the driven shaft.

Foot or flange

The modular design allows flange, foot or shaft mounting.

Vertical too

Vertical V1 and V3 positions are covered by the FKM (Viton) seals in the motor end shield.

Short drive

Against a standard motor plus flange adapter, the product page puts the RFKS axial length saving at 10–20%.

R against F, K and S

Choose the family by where the output has to go. The motor range is the same for all four.

FamilyGear typeOutputChoose it when
RHelicalIn line with the motorThe drive can stay on one axis
FParallel shaftParallel, offsetThe motor has to sit beside the driven shaft
KHelical-bevelRight angleYou need a right angle with high efficiency: up to 95% for the gearbox, longer life on heavy duty
SHelical-wormRight angleA simple conveyor where lower cost and self-locking count

The 95% figure is the K gearbox, not the motor. Gearbox sizes and ratios are not listed here; send yours.

Blue inline helical gear motor on a steel base driving a belt conveyor with cartons, motor bolted directly to the reducer

The motor on an R reducer

What the RFKS motor brings to the input of a helical reducer.

01

Shaft as first pinion

The motor shaft enters the gearbox and drives the first stage. No coupling to misalign, so no vibration from coupling misalignment.

02

Starts under load

The rotor slot profile is made for high starting torque, for loaded conveyors and hoists.

03

Low speed, long hours

The catalog upgrades windings and bearings for low-speed, high-torque duty.

04

Site conditions

Ambient −15 °C to +40 °C, altitude up to 1,000 m with a power derating above that. Class H insulation is available.

The RFKS series

The motor for R, and for F, K and S as well.

Blue inline helical gear motor with a keyed output shaft on a concrete plinth

Aluminum housing motor for gear reducers

RFKS Series Motors

Three-phase asynchronous motor for direct insertion into R, F, K and S gear reducers. Custom shaft extension, FKM oil seals in the end shield, high starting torque. IE3 to IEC 60034-30-1.

0.18–630 kW · 2 · 4 · 6 · 8 · 10 poles · Frames 80–400 · IE3 · IP55

Catalog performance at 380 V, 50 Hz; rated voltage on the product page 220–690 V. Browse the gear motors category.

Where it goes

Conveyors

Belt and roller lines with the drive in line.

Packaging

Machines where a shorter drive frees space.

Farm and process

Grain handling, feeding, compressors and plastics.

Industry pages: Material handling · Agriculture · Manufacturing

Ask about an R drive

Send the reducer, or the output you need.

  • R gearbox size and ratio, or the output speed
  • Kilowatts and poles, or the old motor nameplate
  • Voltage and frequency
  • Foot or flange, and the mounting position
  • Duty: heavy start, low speed, hours per day
Request a quote

Jiangxi Jiawang Special Motor · +86 199 0684 4761 · [email protected] · 1-year warranty on all products

Helical gear motor questions

What is a helical gear motor?

A motor driving a helical gear reducer. In the R family the output shaft is in line with the motor. JWMotor’s RFKS motor is built for direct insertion into the R reducer input.

Helical or helical-bevel?

R helical keeps the output in line. K helical-bevel turns it through a right angle, with gearbox efficiency up to 95% and longer life on heavy duty.

Helical or worm?

S helical-worm also gives a right angle, costs less and is self-locking, which suits simple conveyors. If the drive can stay in line, R is the simpler layout.

Can a helical gear motor mount vertically?

Tell us if it is V1 or V3. The RFKS end shield has an oil seal chamber with FKM (Viton) seals for vertical positions.

Which sizes?

RFKS covers 0.18–630 kW in IEC frames 80–400, with 2 to 10 poles. See the R/F/K/S series page.