IM B5 · Flange mounted · No feet
B5 Flange Motors
A B5 motor has a large flange with through-holes and no feet. It bolts straight onto the machine it drives. The typical case is a close-coupled pump. Our catalog lists B5 for frames 80 to 280. Flange dimensions for each frame are below.
B5 flange dimensions by frame
M is the bolt-circle diameter, N the spigot diameter, P the flange outside diameter, S the bolt-hole diameter and T the spigot depth. D × E is the shaft.
| Frame | Poles | M | N | P | S | T | D × E |
|---|---|---|---|---|---|---|---|
| 80 | 2–8 | 165 | 130 | 200 | 12 | 3.5 | 19 × 40 |
| 90S | 2–8 | 165 | 130 | 200 | 12 | 3.5 | 24 × 50 |
| 90L | 2–8 | 165 | 130 | 200 | 12 | 3.5 | 24 × 50 |
| 100L | 2–8 | 215 | 180 | 250 | 14.5 | 4 | 28 × 60 |
| 112M | 2–8 | 215 | 180 | 250 | 14.5 | 4 | 28 × 60 |
| 132S | 2–8 | 265 | 230 | 300 | 14.5 | 4 | 38 × 80 |
| 132M | 4–8 | 265 | 230 | 300 | 14.5 | 4 | 38 × 80 |
| 160M | 2–8 | 300 | 250 | 350 | 18.5 | 5 | 42 × 110 |
| 160L | 2–8 | 300 | 250 | 350 | 18.5 | 5 | 42 × 110 |
| 180M | 2–8 | 300 | 250 | 350 | 18.5 | 5 | 48 × 110 |
| 180L | 4–8 | 300 | 250 | 350 | 18.5 | 5 | 48 × 110 |
| 200L | 2–8 | 350 | 300 | 400 | 18.5 | 5 | 55 × 110 |
| 225S | 4–8 | 400 | 350 | 450 | 18.5 | 5 | 60 × 140 |
| 225M | 2 | 400 | 350 | 450 | 18.5 | 5 | 55 × 110 |
| 225M | 4–8 | 400 | 350 | 450 | 18.5 | 5 | 60 × 140 |
| 250M | 2 | 500 | 450 | 550 | 18.5 | 5 | 60 × 140 |
| 250M | 4–8 | 500 | 450 | 550 | 18.5 | 5 | 65 × 140 |
| 280S | 2 | 500 | 450 | 550 | 18.5 | 5 | 65 × 140 |
| 280S | 4–8 | 500 | 450 | 550 | 18.5 | 5 | 75 × 140 |
| 280M | 2 | 500 | 450 | 550 | 18.5 | 5 | 65 × 140 |
| 280M | 4–8 | 500 | 450 | 550 | 18.5 | 5 | 75 × 140 |
From the YE3/YE4 flange-mounted dimension table, catalog page 27. The B35 table on page 28 prints the same flange values. Page 27 also lists frames 315 and 355, but the mounting chart on page 5 lists B5 only up to frame 280. For a flange at 315 and above, see B35. Catalog values in mm. Confirm every dimension on the drawing for your order before machining a base, flange or coupling.

Where B5 fits
The machine holds the motor by its flange. Nothing else touches the floor.
01
Close-coupled pumps
The motor flange bolts to the pump. This is the use our customization page gives for B5.
02
Flanged machine inputs
IEC flanges and precise shafts fit straight on, with no extra adapter.
03
Vertical, shaft down
That is V1: flange-mounted vertically, frames 80–355. Frames 180–355 get a rain cap; 80–160 do not.
04
Small frames, face mount
B14 face mounting is listed for frames 80–112.
A flange motor to start from
YE3 keeps IEC flange dimensions, so a flanged replacement bolts to the same face.

IE3 · IEC 60072-1 flange
YE3 Series
Premium-efficiency three-phase induction motor. Shaft heights, foot patterns and flange dimensions follow IEC 60072-1. An existing standard flange stays as it is.
B5 frames 80–280 · IE3 · IP55 · Class F
Water service: our water and wastewater page lists B3, B5 and B14 as standard options.
Where B5 motors go
Pumps
Close-coupled pumps in water, wastewater and building services.
Material handling
Drives that bolt to a flanged input.
Fans
Fans held by the motor flange.
Industry pages: Water and wastewater · Material handling · HVAC and ventilation
Ask for a B5 motor
Tell us the frame, the flange, and what it bolts to.
- Frame size, or kW and poles
- Flange: M, N and P from your machine, or the old motor nameplate
- B5, or V1 if the shaft points down, or B14 for small frames
- Shaft D × E, or a drawing if it differs
- Supply voltage and frequency
- Protection class and quantity
Jiangxi Jiawang Special Motor · +86 199 0684 4761 · [email protected] · 1-year warranty on all products
B5 questions
What is a B5 flange motor?
A motor with a large flange with through-holes and no feet. It is bolted to the driven machine by its flange, which suits close-coupled equipment such as pumps.
Which frames are available as B5?
Frames 80 to 280 on our catalog mounting chart. The flange dimensions for each are in the table above.
What is the difference between B5 and B14?
Both mount by the drive end. B5 uses a large flange with through-holes. B14 is a face mount, listed for frames 80 to 112.
I need a flange on a frame above 280. What then?
The catalog lists B35 (feet and flange) up to frame 400 and V1 up to frame 355. Send your requirement and we confirm the option. See B35 motors.
Will the flange match my old motor?
If the old motor has a standard IEC flange on the same frame, the YE3 flange dimensions are the same. Compare M, N and P with the table, or send the nameplate.
