R helical · in-line output · RFKS · IE3
Helical gear motors
A helical gear motor keeps the drive on one line: the output shaft runs on the same axis as the motor. That is the R reducer family. The RFKS motor goes straight into its input, with no coupling and no adapter. 0.18–630 kW in IEC frames 80–400, to IE3.
Why in-line
An R drive changes the speed, not the direction. The motor and the output share one axis.
Straight layouts
Conveyors, screws and drums where the drive can sit in line with the driven shaft.
Foot or flange
The modular design allows flange, foot or shaft mounting.
Vertical too
Vertical V1 and V3 positions are covered by the FKM (Viton) seals in the motor end shield.
Short drive
Against a standard motor plus flange adapter, the product page puts the RFKS axial length saving at 10–20%.
R against F, K and S
Choose the family by where the output has to go. The motor range is the same for all four.
| Family | Gear type | Output | Choose it when |
|---|---|---|---|
| R | Helical | In line with the motor | The drive can stay on one axis |
| F | Parallel shaft | Parallel, offset | The motor has to sit beside the driven shaft |
| K | Helical-bevel | Right angle | You need a right angle with high efficiency: up to 95% for the gearbox, longer life on heavy duty |
| S | Helical-worm | Right angle | A simple conveyor where lower cost and self-locking count |
The 95% figure is the K gearbox, not the motor. Gearbox sizes and ratios are not listed here; send yours.

The motor on an R reducer
What the RFKS motor brings to the input of a helical reducer.
01
Shaft as first pinion
The motor shaft enters the gearbox and drives the first stage. No coupling to misalign, so no vibration from coupling misalignment.
02
Starts under load
The rotor slot profile is made for high starting torque, for loaded conveyors and hoists.
03
Low speed, long hours
The catalog upgrades windings and bearings for low-speed, high-torque duty.
04
Site conditions
Ambient −15 °C to +40 °C, altitude up to 1,000 m with a power derating above that. Class H insulation is available.
The RFKS series
The motor for R, and for F, K and S as well.

Aluminum housing motor for gear reducers
RFKS Series Motors
Three-phase asynchronous motor for direct insertion into R, F, K and S gear reducers. Custom shaft extension, FKM oil seals in the end shield, high starting torque. IE3 to IEC 60034-30-1.
0.18–630 kW · 2 · 4 · 6 · 8 · 10 poles · Frames 80–400 · IE3 · IP55
Catalog performance at 380 V, 50 Hz; rated voltage on the product page 220–690 V. Browse the gear motors category.
Where it goes
Conveyors
Belt and roller lines with the drive in line.
Packaging
Machines where a shorter drive frees space.
Farm and process
Grain handling, feeding, compressors and plastics.
Industry pages: Material handling · Agriculture · Manufacturing
Ask about an R drive
Send the reducer, or the output you need.
- R gearbox size and ratio, or the output speed
- Kilowatts and poles, or the old motor nameplate
- Voltage and frequency
- Foot or flange, and the mounting position
- Duty: heavy start, low speed, hours per day
Jiangxi Jiawang Special Motor · +86 199 0684 4761 · [email protected] · 1-year warranty on all products
Helical gear motor questions
What is a helical gear motor?
A motor driving a helical gear reducer. In the R family the output shaft is in line with the motor. JWMotor’s RFKS motor is built for direct insertion into the R reducer input.
Helical or helical-bevel?
R helical keeps the output in line. K helical-bevel turns it through a right angle, with gearbox efficiency up to 95% and longer life on heavy duty.
Helical or worm?
S helical-worm also gives a right angle, costs less and is self-locking, which suits simple conveyors. If the drive can stay in line, R is the simpler layout.
Can a helical gear motor mount vertically?
Tell us if it is V1 or V3. The RFKS end shield has an oil seal chamber with FKM (Viton) seals for vertical positions.
Which sizes?
RFKS covers 0.18–630 kW in IEC frames 80–400, with 2 to 10 poles. See the R/F/K/S series page.
