Close-up of the nameplate on a blue three-phase motor on the production line

Specify or replace one unit · RFKS · IE3

Gearmotor

Need one gearmotor, built or replaced? Two nameplates and four facts are usually enough for a first quote that fits. This is the checklist we work from for the RFKS motor on R, F, K and S reducers.

2 nameplatesMotor and gearbox
PositionHorizontal, V1 or V3
SupplyVoltage and frequency
DutyStarts, speed, hours

The buyer checklist

Send what you can. Photos are fine. Each line removes a question we would otherwise have to ask.

What to sendWhere to find itWhy it matters
Gearbox family, size, ratioGearbox nameplateFixes the input the motor has to fit, and the output speed
Kilowatts and polesMotor nameplate (poles from the r/min)Sets the power and the speed into the gearbox
Voltage and frequencyMotor nameplate, or your supplyCatalog data is at 380 V, 50 Hz; the product page lists 220–690 V
Mounting positionThe machineHorizontal, or vertical V1 or V3 where the oil seal matters most
Mounting typeThe machineFlange, foot or shaft mounting
DutyThe operatorHeavy starts, long hours at low speed, frequent stops

New to motor plates? Our guide to reading a motor nameplate walks through each field.

Blue right-angle gear motor on a steel workbench with a vernier caliper and tape measure beside it

No readable plate?

Plates fade, and some gearboxes come without one. Then the machine tells us what the plate would have.

01

Photos from three sides

The motor and gearbox together, the joint between them, and the output shaft.

02

Flange and shaft

Measure the flange and shaft if you can. Shafts can be made to your drawing.

03

The old motor’s frame

The model code carries the frame height. In RFKS 132M-4, 132 is the frame height in millimetres, M the core length and 4 the poles.

04

What the machine does

Conveyor, hoist, mixer, and how fast the output turns.

The motor we quote: RFKS

The checklist points to one series. The frame-by-frame table is on the series page.

Blue gear motor strapped to a wooden pallet in a dispatch area

Aluminum housing motor for gear reducers

RFKS Series Motors

Three-phase asynchronous motor for direct insertion into R, F, K and S gear reducers. Custom shaft extension, FKM oil seals in the end shield, high starting torque. IE3 to IEC 60034-30-1.

0.18–630 kW · 2 · 4 · 6 · 8 · 10 poles · Frames 80–400 · IE3 · IP55

Example from the catalog: RFKS 132M-4 is 7.5 kW at 1470 r/min with 90.4% efficiency. Ambient −15 °C to +40 °C, altitude up to 1,000 m with a power derating above that. Class H insulation is available. SEW and Nord are trademarks of their owners. JWMotor is not affiliated with them.

Three kinds of request

A failed motor

The gearbox still runs. Send both plates and the mounting position.

A new machine

Send the output speed and torque you need, and the mounting.

A spare on the shelf

Send the plates of the units in service.

Mounting, voltage and shaft options are on the customization page.

Send the nameplates

One message with the plates and the position is usually enough to start.

  • Gearbox family, size and ratio: R, F, K or S
  • Motor kilowatts and poles, or a photo of the plate
  • Voltage and frequency
  • Mounting position and type
  • Duty: heavy start, low speed, hours per day
  • Ambient temperature, and altitude if above 1,000 m
Send the nameplates

Jiangxi Jiawang Special Motor · +86 199 0684 4761 · [email protected] · 1-year warranty on all products

Before you order

What do you need to quote one gearmotor?

The gearbox family, size and ratio, the motor kilowatts and poles, the supply voltage and frequency, the mounting position and the duty. Photos of both nameplates cover most of it.

The gearbox plate is missing. Can you still quote?

Send photos of the motor and gearbox, the joint between them and the output shaft, plus what the machine does and how fast the output turns. We tell you what else we need.

Will the RFKS motor fit my existing reducer?

RFKS is built for direct insertion into R, F, K and S reducers, and the product page says it follows international standard dimensions. We confirm the fit for your gearbox before quoting.

Which voltages?

The catalog lists performance at 380 V, 50 Hz. The product page gives a rated voltage range of 220–690 V. Tell us your supply.

Is there a warranty?

Yes. One year on all products.