Row of green flange motors with bare shaft extensions on a workshop rack

Replace the motor · or look at the whole unit

Motor or complete gear motor

When a gear drive stops, the first question is which half failed. If the reducer still runs, the motor alone can often be replaced: the RFKS motor goes straight into R, F, K and S reducer inputs. If the gearbox itself is worn, a new motor will not fix it.

Motor onlyRFKS into the existing reducer
R · F · K · SReducer inputs it fits
10–20%Shorter than motor plus adapter
IE3IEC 60034-30-1

Motor only, or the whole unit

A quick way to tell. We confirm it from the plates and photos.

Replace the motorLook at the whole unit
The gearboxRuns quietly and holds its oilNoisy, leaking at its own seals, or worn at the output
The faultMotor trips, overheats or will not startThe output shaft or bearings are damaged
What you sendBoth nameplates and the mounting positionBoth nameplates, photos and a description of the fault
What we supplyAn RFKS motor for direct insertion into the reducer inputWe tell you what we can supply for the drive
Blue gear reducer and a separate blue motor side by side on a steel workbench, the motor shaft facing the reducer input

Replacing the motor alone

RFKS is built to go into the reducer, not onto an adapter. That keeps the replacement short.

01

Straight into the input

Custom shaft extension and end shield. The shaft becomes the gearbox’s first-stage pinion, with no coupling to misalign.

02

The oil stays in

An oil seal chamber in the end shield with high-temperature FKM (Viton) seals, including vertical V1 and V3.

03

Standard dimensions

The product page says RFKS follows international standard dimensions and can replace many SEW-style or Nord-style units.

04

Less downtime

The gearbox stays on the machine. Only the motor comes off.

The replacement motor: RFKS

Frame-by-frame data is on the series page.

Blue flange motor with a short shaft extension on a workbench beside an open carton

Aluminum housing motor for gear reducers

RFKS Series Motors

Three-phase asynchronous motor for direct insertion into R, F, K and S gear reducers. Custom shaft extension, FKM oil seals in the end shield, high starting torque. IE3 to IEC 60034-30-1.

0.18–630 kW · 2 · 4 · 6 · 8 · 10 poles · Frames 80–400 · IE3 · IP55

SEW and Nord are trademarks of their owners. JWMotor is not affiliated with them. JWMotor does not sell SEW-branded units; “fits” refers to the RFKS motor on these reducer types.

Typical cases

Failed motor, good gearbox

The most common case. Send both plates.

Upgrade to IE3

Replace an older motor on a working gearbox with an IE3 RFKS.

Whole drive in doubt

Send photos and the fault, and we will say what we can do.

Mounting, voltage and shaft options are on the customization page.

Ask what to replace

Send the plates and the symptoms. We will tell you whether the motor alone will do.

  • Gearbox family, size and ratio: R, F, K or S
  • Motor kilowatts and poles, or a photo of the plate
  • What failed, and how it shows
  • Voltage and frequency
  • Mounting position, including vertical V1 or V3
  • Duty: heavy start, low speed, hours per day
Ask what to replace

Jiangxi Jiawang Special Motor · +86 199 0684 4761 · [email protected] · 1-year warranty on all products

Motor or gear motor?

Can I replace only the motor on my gear motor?

Often, yes, if the gearbox still runs well. RFKS motors are built for direct insertion into R, F, K and S reducer inputs. Send both nameplates and the mounting position and we confirm the fit.

How do I know the gearbox is the problem?

Noise from the gearbox, oil leaking at its own seals, or damage at the output shaft point to the gearbox. A motor that trips, overheats or will not start points to the motor. Photos help us tell.

Do you supply the gearbox too?

Our catalog series for gear drives is the RFKS motor. Tell us about the gearbox and we will say what we can supply.

Do you sell SEW or Nord units?

No. SEW and Nord are trademarks of their owners. JWMotor is not affiliated with them. RFKS follows international standard dimensions and can replace many SEW-style or Nord-style units.

Will the new motor leak oil?

The end shield has an oil seal chamber with high-temperature FKM (Viton) seals, aimed at seepage at the gearbox interface, including V1 and V3.