Row of grey motors on a blue workshop shelf, fan cowls toward the camera

Gear reducer motors · IE3 · Frames 80–400

R/F/K/S series motors

Three-phase motors built to go straight into R, F, K and S gear reducers. The shaft extension enters the gearbox and works as its first-stage pinion. No coupling, no flange adapter. The RFKS catalog runs from 0.18 kW to 630 kW, IEC frames 80 to 400, 2 to 10 poles, to IE3.

0.18–630 kWPower in the catalog
2 · 4 · 6 · 8 · 10Poles
80–400IEC frame
IE3IEC 60034-30-1

One motor, four gearbox families

R, F, K and S are four gear reducer families. RFKS motors carry the oil seal and shaft extension each of them needs at the input. The gearbox decides the output. The motor decides the power and speed going in.

R

Helical

Input and output on one line. No change of direction.

F

Parallel shaft

Output shaft parallel to the motor, offset to one side.

K

Helical-bevel

A right-angle drive. The product page gives K gearboxes efficiency up to 95% and longer life for heavy duty.

S

Helical-worm

A right-angle drive that costs less. The product page notes a self-locking feature for simple conveyors.

The 95% figure is the efficiency of the K gearbox, not of the motor. The modular design allows flange, foot or shaft mounting, so the drive can fit a cramped layout.

Blue gear reducer with a motor bolted directly to its input, no coupling between them

Why there is no adapter

A standard IEC motor on a gearbox needs a lantern adapter and a coupling. RFKS removes both. The motor end shield mates with the gearbox input.

01

The shaft is the first pinion

The motor shaft extends into the gearbox and drives the first stage. No coupling to misalign, so no vibration from coupling misalignment.

02

10–20% shorter

Against a standard motor plus flange adapter, the product page puts the axial length saving at 10–20%. That matters on AGVs, conveyor lines and packaging machines.

03

Oil stays in the gearbox

The end shield has an oil seal chamber with high-temperature FKM (Viton) seals. It is there for seepage at the gearbox interface, including vertical mounting positions V1 and V3.

04

Starts under load

The rotor slot profile is made for high starting torque. Hoists and loaded conveyors are the starts it is meant for.

05

Built for low speed and high torque

The catalog describes an integrated input, a reinforced flange and a precision shaft system for alignment. Windings and bearings are upgraded for long hours at low speed and heavy load.

06

Site conditions

Ambient −15 °C to +40 °C (+5 °F to +104 °F). Altitude up to 1,000 m, with a power derating above that. Catalog rows are IP55 with Class F insulation. Class H is available for hot sites.

Power by frame in the catalog

Pick the frame from the power and pole count, then match it to the gearbox input. Model codes read like the rest of the range: in RFKS 132M-4, 132 is the frame height in millimetres, M the core length, and 4 the pole count.

IEC framePower in the catalogPoles
800.18–1.1 kW2, 4, 6, 8
900.37–2.2 kW2, 4, 6, 8
1000.75–3 kW2, 4, 6, 8
1121.5–4 kW2, 4, 6, 8
1322.2–7.5 kW2, 4, 6, 8
1604–18.5 kW2, 4, 6, 8
18011–22 kW2, 4, 6, 8
20018.5–37 kW2, 4, 6
22518.5–45 kW2, 4, 6, 8
25030–55 kW2, 4, 6, 8
28037–110 kW2, 4, 6, 8
31545–220 kW2, 4, 6, 8, 10
35590–355 kW2, 4, 6, 8, 10
400315–630 kW2, 4, 6, 8

By pole count: 2-pole 0.75–630 kW, 4-pole 0.55–630 kW, 6-pole 0.37–500 kW, 8-pole 0.18–400 kW, and 10-pole 45–185 kW on frames 315 and 355. Catalog performance is listed at 380 V, 50 Hz; the largest frame-400 ratings are listed at 660 V. Rated voltage on the product page is 220–690 V. As an example, the RFKS 132M-4 is 7.5 kW at 1470 r/min with 90.4% efficiency.

Replacing the motor on an existing gearbox

The catalog describes RFKS as made to fit the four main SEW reducer platforms. The product page says the series follows international standard dimensions and can replace many SEW-style or Nord-style units. We confirm the fit before we quote.

Read the gearbox plate

Family (R, F, K or S), size and ratio. That fixes the input the motor has to match.

Read the motor plate

Kilowatts, poles, voltage and frequency. Frame code if it is there.

Note the position

Horizontal, or vertical V1 or V3. Vertical positions are where the seal matters most.

Describe the duty

Heavy starts, long hours at low speed, or frequent stops. It decides the winding and bearings.

The RFKS series

One series for all four reducer families, from fractional kilowatts to 630 kW.

Blue flange-mounted motor with a short shaft extension for a gear reducer input

Aluminum housing motor for gear reducers

RFKS Series Motors

Three-phase asynchronous motor for direct insertion into R, F, K and S gear reducers. Custom shaft extension, FKM oil seals in the end shield, high starting torque. IE3 to IEC 60034-30-1.

0.18–630 kW · 2–10 poles · Frames 80–400 · IE3

Where RFKS goes

Lines and packaging

Automated lines, conveyors, AGVs and packaging machines, where a shorter drive frees space.

Heavy starts

Hoists and conveyors that start under load.

Farm and process

Grain handling, ventilation and feeding on the farm. Compressors, plastics and general processing in the plant.

Industry pages: Material handling · Agriculture · Manufacturing

Send the gearbox

The gearbox decides the input. Send it with the motor, and the first quote can be the right one.

  • Gearbox family, size and ratio: R, F, K or S
  • Kilowatts and poles, or the old motor nameplate
  • Voltage and frequency
  • Mounting position, including vertical V1 or V3
  • Duty: heavy start, low speed, hours per day
  • Ambient temperature and altitude if above 1,000 m
Request a quote

Jiangxi Jiawang Special Motor · +86 199 0684 4761 · [email protected]

Before the quote

What is an R/F/K/S series motor?

A three-phase motor made for direct insertion into R (helical), F (parallel shaft), K (helical-bevel) and S (helical-worm) gear reducers. Its shaft extension goes into the gearbox and acts as the first-stage pinion, so no coupling or flange adapter is needed.

How is it different from a standard IEC motor with an adapter?

It is shorter and has fewer parts. The product page gives a 10–20% reduction in axial length against a standard motor plus flange adapter. Without a coupling there is no coupling misalignment to cause vibration.

K or S gearbox?

K (helical-bevel) gives higher efficiency, up to 95% for the gearbox, and longer life on heavy duty. S (helical-worm) costs less and is self-locking, which suits simple conveyors. The same RFKS motor range covers both.

Will it fit my SEW-style or Nord-style gearbox?

The catalog describes RFKS as made to fit the four main SEW reducer platforms, and the product page says it can replace many SEW-style or Nord-style units. Send the gearbox family, size and ratio with the old motor nameplate, and we will confirm the fit before quoting.

What sizes are in the catalog?

0.18–630 kW in IEC frames 80–400. 2-pole runs 0.75–630 kW, 4-pole 0.55–630 kW, 6-pole 0.37–500 kW, 8-pole 0.18–400 kW, and 10-pole 45–185 kW on frames 315 and 355.

What efficiency class is it?

IE3 premium efficiency to IEC 60034-30-1. Catalog efficiency on 4-pole models runs from 80.8% at 0.55 kW to 96.0% at 630 kW.

Does it leak oil when mounted vertically?

The end shield has an oil seal chamber with high-temperature FKM (Viton) seals, aimed at seepage at the gearbox interface, including the vertical positions V1 and V3. Tell us the mounting position when you ask for a quote.