Cast-iron motor on a steel base in a factory

IE3 · 0.75–630 kW · frames 80–400

YE3 series motors

Three-phase induction motors, IE3, IP55, Class F. 0.75–630 kW, poles 2, 4, 6, 8 and 10, IEC frames 80–400, 220–690 V.

The published range

These figures are the YE3 product range. The series page holds the model list.

0.75–630 kWPower
2 · 4 · 6 · 8 · 10Poles
80–400IEC frame
220–690 VRated voltage

01

IE3 premium efficiency

Three-phase induction motor at IE3, to IEC 60034-30-1. Fewer losses than an IE2 motor, from the materials and the design. Meets MEPS in the EU, South America and Asia.

02

IP55

IP55 protection is standard on the YE3 series.

03

Copper and Class F

W470/W600 cold-rolled silicon steel and 100% copper windings. Class F insulation, 155°C, assessed at a Class B rise of 80K. Class H is available for hotter rooms.

04

1,000 m, voltage within 5%

Stated altitude is 1,000 m. Voltage tolerance is within 5%. Above that altitude, derate.

Same shaft height as the motor it replaces

Foot pattern and flange follow IEC 60072-1, so the base and the coupling stay when the frame is a standard IEC frame. The series runs from frame 80 to frame 400.

  • IEC 60072-1 shaft height, feet and flange
  • Frames such as 132M and 160L
  • Siemens, ABB and WEG IE1 motors on a standard IEC frame
Shaft keyway and cast foot of an industrial motor

YE3 series

One catalog line. The product page carries the model designation and the full grid.

YE3 motor

IE3 · IP55 · 0.75–630 kW

YE3

Poles 2, 4, 6, 8 and 10. IEC frames 80–400. Rated voltage 220–690 V.

Where the series is used

The series page names mines, conveyors, compressors, plastics and general processing.

Cast-iron motor coupled to a mill drive in a dusty plant

Mines

Cast iron, for high torque and dust.

Cast-iron motor coupled through a gearbox to a conveyor

Conveyors

Three-phase conveyor drives.

Cast-iron motor coupled to an air compressor

Compressors

Compressors, plastics and general processing.

Quote from the model or the plate

Send the YE3 model if you have it. Otherwise send the nameplate of the motor being replaced.

  • Frame, 80–400
  • kW, 0.75–630
  • Poles: 2, 4, 6, 8 or 10
  • Voltage, 220–690 V, and frequency
  • Foot or flange mounting
  • IE3

YE3 can run on a frequency converter. Cables over 50 m, or voltage over 500 V, need a filter. Regional voltage and mounting sit on customization. Send the plate through contact.

Questions before the order

What does the YE3 series cover?

Three-phase induction motors, IE3, IP55, Class F. Power 0.75–630 kW, poles 2, 4, 6, 8 and 10, IEC frames 80–400, rated voltage 220–690 V.

Will it fit the existing base?

YE3 follows IEC 60072-1. Shaft centre height, foot pattern and flange match a standard IEC frame. Frames such as 132M and 160L line up with the bolt spacing. The series page names Siemens, ABB and WEG IE1 motors when that frame is standard.

What site conditions does the series page state?

IP55. Class F insulation at 155°C, assessed at a Class B rise of 80K. Class H is available for hotter rooms. Altitude up to 1,000 m, voltage within 5%. Higher altitude needs a power derating. A frequency converter is acceptable. Cables over 50 m, or voltage over 500 V, need a filter. The same cast-iron housing is used for high torque and dust in mines.